SLA, DLP and LCD: resin printing in detail
How resin printing works, how SLA, DLP and MSLA differ, what accuracy is achievable and what washing and post-curing involve.
As of November 2026
In resin printing the part is formed from liquid resin that hardens under UV light. The technical name for the family is vat photopolymerisation. It delivers the finest detail of all common plastic processes.
Three variants
| Variant | Light source | Characteristic |
|---|---|---|
| SLA | laser spot steered by mirrors | very even quality, slower with full build platforms |
| DLP | projector exposes the whole layer | fast, resolution depends on the projector |
| MSLA / LCD | UV LEDs behind an LCD screen | inexpensive, the standard for home machines |
On most machines the part hangs upside down from a platform that is drawn out of the resin bath layer by layer.
Typical values
| Quantity | Usual range |
|---|---|
| Layer height | 0.025 to 0.1 mm |
| In-plane resolution | about 0.02 to 0.05 mm |
| Dimensional tolerance | about ±0.1 to ±0.2 mm or ±0.5 % |
| Minimum wall thickness | 0.5 mm supported, 1 mm free-standing |
| Smallest detail | about 0.2 mm |
What happens after printing
A resin part is not finished when the printer stops. Fixed steps follow:
- Draining and removal from the build platform.
- Washing in isopropanol or a cleaning agent to remove liquid resin.
- Drying.
- Post-curing under UV light, often at raised temperature. Only now does the material reach its final strength.
- Removing supports and sanding the contact points.
Design notes
- Print hollow. Solid parts use a lot of resin and tend to build stress. Walls of 2 to 3 mm usually suffice.
- Add drain holes. Cavities need at least two openings of about 3 mm so resin can flow out and air can enter.
- Tilt the part. Parts are usually printed at 30 to 45 degrees so each layer's area stays small.
- Plan for supports. Nearly every part needs them. Put visible faces on the side away from the supports.
Resin types
- Standard resin: detailed, brittle, for display models
- Tough (ABS-like) resin: for housings and snap fits
- Flexible resin: rubbery
- High-temperature resin: for moulds and parts near heat
- Castable resin: burns out cleanly, for jewellery investment casting
- Dental and biocompatible resins: certified for their purpose
- Clear resin: almost transparent after polishing
Strengths
- very smooth surfaces with barely visible layers
- the finest detail and sharp edges
- even strength in all directions
- dense, watertight parts
Limits
- resin is a hazardous substance: gloves, ventilation and careful disposal are mandatory
- parts are often more brittle than FDM or nylon parts
- many resins yellow and embrittle in sunlight
- smaller build volumes, higher material cost
- post-processing is always part of the job
What resin printing is the first choice for
Miniatures and figures, jewellery patterns, dental work, small precision parts, masters for silicone moulds, transparent parts and design samples with a high-quality surface.
FAQ
Is cured resin harmless?
Fully cured parts are considered far less critical than liquid resin. For skin contact, food or medical purposes you still need a material approved for that use and a documented process.
Why does resin printing smell?
Liquid resin and isopropanol give off volatile substances. A resin printer belongs in a well-ventilated room, not a living room or bedroom.
More topics
- FDM / FFFPlastic filament is melted and laid down in lines. The most widespread process.
- SLSA laser fuses nylon powder. Durable parts without supports.
- MJFPowder is fused across the whole layer with ink and heat. Fast and series-ready.
- MetalLaser melting and related processes for steel, aluminium and titanium.