FDM printing (FFF): how it works, strengths, limits and typical values
Fused deposition modelling in detail: printer anatomy, temperatures, layer heights, accuracy, supports, cost and the most common uses.
As of November 2026
FDM stands for fused deposition modelling, FFF for fused filament fabrication. Both mean the same thing: a plastic filament is melted and built up line by line into a part. It is by far the most widely used process, from hobby machines to industrial equipment.
How an FDM printer works
The filament, a wire usually 1.75 mm thick, is pushed by an extruder into the heated print head (hotend). There it melts and leaves through a nozzle, normally with a 0.4 mm opening. The head traces the outline of each layer and then fills the inside. The machine then moves by one layer height and prints the next. A fan cools the fresh material so that it keeps its shape.
The first layer sticks to a heated build plate. Its quality decides whether the print succeeds.
Typical values
| Quantity | Usual range |
|---|---|
| Nozzle diameter | 0.2 to 0.8 mm, standard 0.4 mm |
| Layer height | 0.08 to 0.3 mm |
| Nozzle temperature | 190 to 300 °C depending on material |
| Bed temperature | 50 to 110 °C |
| Dimensional tolerance | about ±0.2 to ±0.5 mm or ±0.5 % |
| Minimum wall thickness | 0.8 mm, 1.2 mm or more recommended |
| Build volume, home machines | roughly 220 to 350 mm per side |
| Build volume, industrial | up to more than 1 m |
What the inside of an FDM part looks like
A printed part is rarely solid. It has three zones:
- Walls (perimeters): the outer lines. Two to four are usual. They carry most of the load.
- Top and bottom layers: several closed layers above and below.
- Infill: a lattice inside, usually 10 to 40 percent dense.
To make a part stronger, raise the number of wall lines first. More infill does less.
Supports
Material cannot be printed in mid-air. Overhangs up to about 45 degrees work unaided; shallower ones need supports. These are printed along with the part and snapped off afterwards. The surface stays rougher where they touched. Machines with two materials can print supports in a soluble plastic that dissolves in water.
Strength depends on direction
Within a layer the lines are well fused. Between layers the bond is weaker. An FDM part therefore takes considerably more load in the layer plane than across it, only 40 to 80 percent depending on material and settings. Designers place tensile loads along the layers.
Strengths
- lowest cost per part and per machine
- widest choice of materials and colours
- large parts are possible
- a clean, dry process without chemicals
- multicolour and multi-material prints
Limits
- visible layer lines
- fine details below about 0.5 mm are lost
- supports leave marks
- strength depends on print orientation
- round holes and fits need allowance or finishing
What FDM is the first choice for
Housings, brackets, jigs, spare parts, functional prototypes, large models, coarse-scale architectural models, flexible TPU parts and anything that has to be cheap and available quickly.
FAQ
How long does an FDM print take?
A part the size of a coffee mug needs two to eight hours depending on layer height and infill. Print time grows with volume and falls with coarser layers.
Can FDM print several colours?
Yes. Systems with a filament changer or several nozzles print in multiple colours. Each colour change purges material, which costs time and filament.
Our own service: 3D Druck Berlin prints in FDM only. Upload a file for an instant quote, or read their FDM design rules.
More topics
- SLA / resinLiquid resin is cured with light. For the finest detail and smooth faces.
- SLSA laser fuses nylon powder. Durable parts without supports.
- MJFPowder is fused across the whole layer with ink and heat. Fast and series-ready.
- MetalLaser melting and related processes for steel, aluminium and titanium.