Designing for 3D printing: the rules for every process
Wall thickness, overhangs, holes, lettering, threads and snap hooks: design guide values for FDM, SLA and SLS side by side.
As of November 2026
A part designed for printing costs less, withstands more and comes out usable at the first attempt. The following guide values apply to the three common plastic processes.
Guide values compared
| Feature | FDM | SLA | SLS / MJF |
|---|---|---|---|
| Minimum wall thickness | 0.8 mm | 0.5 mm | 0.7 mm |
| Recommended wall thickness | 1.2 to 3 mm | 1 to 2.5 mm | 1 to 3 mm |
| Overhang without support | up to 45° | up to about 30° | any |
| Smallest detail | 0.8 mm | 0.2 mm | 0.5 mm |
| Smallest hole | 2 mm | 0.5 mm | 1.5 mm |
| Raised lettering, stroke width | 0.6 mm | 0.3 mm | 0.6 mm |
| Clearance for moving parts | 0.4 mm | 0.2 mm | 0.5 mm |
Wall thickness
Walls that are too thin break or do not print at all. Walls that are too thick cost material, lengthen the print and warp. An even wall thickness throughout is better than varying ones. Where stiffness is lacking, ribs help more than extra mass.
Overhangs and supports
Every layer needs something to rest on. In FDM, slopes up to 45 degrees succeed. Anything shallower needs support material. Ways to avoid it:
- chamfers instead of fillets on undersides
- teardrop-shaped holes across the print direction
- splitting the part and gluing it after printing
- choosing a different orientation
Holes and fits
Printed holes come out a little small. For FDM, add 0.1 to 0.2 mm to the diameter. For accurate fits, drill or ream after printing. Holes printed vertically are rounder than horizontal ones.
Corners and edges
Sharp inside corners concentrate stress and are typical break points. A radius of 1 mm or more helps noticeably. Outside edges with a small chamfer or round feel better and wear less.
Lettering and detail
- use a sans-serif typeface
- engraved lettering is more robust than raised
- lettering is cleanest on top faces
- minimum letter height in FDM is about 5 mm
Threads
- Printed threads work from about M6.
- Below that, heat-set brass inserts or cut the thread afterwards.
- Self-tapping screws for plastic hold in a hole of about 85 percent of the screw diameter.
- For joints that are opened often, always use inserts.
Snap hooks
- make them long and slim so the strain stays small
- add a radius at the root
- in FDM, print them lying down so the layers run along the hook
- choose a tough material: PETG, PA or ABS, not PLA
Splitting parts
Whatever does not fit the build volume or would need too many supports is split. Locating pins, tongue and groove or dovetails make alignment easier. Plan glue faces as large as possible.
Think about orientation
The position in the printer affects strength, surface, accuracy and price all at once. If you know which face is visible and where the force acts, tell the manufacturer.
FAQ
Do I have to design supports myself?
No. The slicer generates them automatically. Clever design can often make them unnecessary, though.
How much clearance does a lid need?
For a lid removable by hand in FDM, about 0.2 to 0.3 mm all round. For a press fit, 0.1 mm.
Our own service: FDM-specific guide values with examples are on 3D Druck Berlin under FDM design rules. Logo objects have their own dimensions, explained by Brandform under design rules for logo objects.
More topics
- Tolerances and fitsWhat accuracy is realistic and how to design fits.
- Slicer settingsWhich setting does what, and where to start.
- Post-processingFrom raw print to finished part: sanding, painting, gluing, inserts.
- Fixing print defectsThe typical faults, their causes and what helps.
- CAD programsFrom browser building blocks to parametric CAD: what suits whom.
- 3D scanningPhotogrammetry, structured light, laser: what a scan delivers and where it ends.
- The first printFrom unboxing to the first successful part.
- Buying a 3D printerDesigns, features, price classes and running costs, without brand advertising.
- Finding modelsWhere ready-made 3D models are and how to spot good ones.